Week 8: Final Assembling

It is the final week of the DTSF project, so I will need to finish everything. Immediately, I started drilling a hole for wires to go through the box. Then I would lure the cables through the handle to the box and connect to the circuitry.

It was one of the hardest in the assembling section, as everything was delicate and I felt like it could break anytime if I was too harsh on it. After that, I needed to test it out to see if it is still working or not, and thankfully, everything went quite well.

Now it is just a matter of gluing everything together and the results are in. I got it together and it worked flawlessly, everything was in the box and when I turned the switch on, it was working well. Finally, I went ahead and test out all the fan blades with everything attached together and have a board full of results based on their speed.

In the end, I decided to go with the 13 blades black one, since it had significantly higher speed than other ones and more stability when running, an element that would ensure my fan wouldn’t break while running.

And that had basically wrapped up my DTSF project for this summer. While I had achieved what I initially set in the beginning, there was still room for improvement, quite a lot actually. There were numerous types of fan blades that I could have printed out and examined but I did not have the time to do it, so expanding on that would be a great way to reach further goals in this project. Another thing was that I had only started measuring different fan blades in the last few weeks, therefore a lot of the variables in measurement were not carefully taken into consideration and thus, the results had been varying a lot. I would need to find out a more consistent method for measuring the airflow for this project. And finally, the fan’s body could have been designed differently so that it would be easier to customize/change the batteries, the codes, or upgrade the components I supposed.

8 weeks flew by really fast, even now I still remembered that first week in which I got no clue where to start or what to look for, and now I managed to finish the project I planned out at the beginning. The early weeks were a bit troublesome to me and I was behind on some parts of the program, but as time went by, I managed to pick up momentum and got to where I wanted. The project helped me a lot with self-learning, troubleshooting, and what’s more, I got some mechanic skills such as soldering and 3D printing, drilling that would be fun to apply to some of my projects later on. Another thing to notice that was my public speaking skills got better after those practice talks, and I am really grateful for that.

It’s been a pleasure for me to take part in DTSF 2023, and special thanks to Eric and Josh for giving me this opportunity as well as helping me out a lot during the fellowship. And finally, thank you to Sami, Akriti, and Josie as well for being with me on this fellowship and giving me a fun ride. Until next time!

Week 7: Final printing and testing

This week is often known as crunch time for the DTSF, as we needed to get everything ready for the next week for the final presentation. The week started with me printing even more fan blades out for testing, as our tool for air flow measurement will be arriving later on in the week. I rely heavily on this one fan generator that allowed you to customize the fan blade number, the offset, etc. easily by just changing numbers on the text file.

Next up was deciding whether or not to have the solar panel with the fan or leave it aside. After careful consideration, I decided to make it separate from the fan. But then it would be inconvenient for general use as you need to connect the wires so I made a barrel connection out of those. I could only find a DC connector which was the female part, so for the male part, I just cut off the head of a power supply wiring and wired it up to the solar panel.

After making sure that it was working properly, I went ahead and soldered everything together and I got a solar energy charger!

The final designs for the fan’s body were also coming in, I made various changes compared to the last one, and the new one was looking like this in the program.

And well, everything was a tad too short to fit the whole circuit in, which indicated I had to enlarge it, but I didn’t measure it carefully but just eyeball it, thus I ended up overshooting the size of the body again.

Now I really had to measure precisely and drew it out for easier understanding, and in the end, my design was looking like this.

It was a bit different from the other design I had, as instead of having the handle part under the box of circuitry, I had it up on the box.

Finally, I measured most of the fans I had til this moment, excluding some that didn’t perform well, using the BT meter machine and wrote down the different results.

And that was this week gone, and phew, times flew by fast. Hopefully, in the next week, I will be able to finish assembling everything together and get my stuff ready for my presentation on Monday.

Week 6: Sudden roadblock

After finishing everything for the circuit last week, I started to focus on printing many different designs for my fan and the body as well.

The body parts printed out great, but it’s a bit larger than what I would need. In addition, it would block the wind from the fans if my motor stayed like in the picture.

I continued printing out various types of fan blades to test out and after a long session, I finally managed to get one working really well. (insert video)

However, it would occur to me that the temp sensor was not working after testing some fans, as shown in the video.

(In the video although the sensor worked when I plugged in the laptop and show reading, as soon as I unplugged, it just went max speed due to my code, which indicated to me that the Arduino was working but not the temperature sensor. My code was if a certain temperature was detected, it would correspond to a certain speed around that temperature range. (see week 3 for a more detailed explanation)). I troubleshoot it by simply replacing a different temperature sensor model (DHT11) and it worked flawlessly, even without connecting to PC.

I also went ahead and changed the algorithm for the speed, instead of using the if… else for a certain speed fan at a temperature range, I gave it a formula that the fan speed would be 7 times the temperature ( in Celsius). Therefore, the max speed it could spin would be corresponding to around 36 degrees Celcius, which is roughly around 96 degrees Fahrenheit.

Now I really have a fully functioning circuit that could work independently, and now my attention is to finalize my body design and choose what fan blades I really want for using. Ideally, I should have my body and fans finalized by Thursday and start assembling on Friday and Monday. Hopefully, I will be finishing all that in the upcoming week, as most of week 8 we will be focusing on our presentation rather than our projects.

Week 5: Finishing the circuitry

This week had me focusing entirely on the fan’s circuit to resolve it once and for all. I tried to rewire everything precisely like last week to test out the consistency of the board but this time, even with a little help, I could not even manage to get it running. I would come to notice that probably the tape was not enough to hold everything together, and thus I came and revisit the soldering station, this time with Eric’s help.

After that, we managed to get it spinning with the solder, which took me one step closer to the finish line.

In addition, I also added an on/off switch for the circuit to control the fan.

For more realistic experimentation, I decided to go outside to fully utilize the power from the solar panel. Despite that, it still wouldn’t have enough power if I only had a battery as a power source for the whole circuit.

With a little bit of help from my laptop, however, things seem to go pretty smoothly. I figure that it might be something wrong with my code so I went and double check my code but although my code was wrong, it was not the problem for the fact that the motor was not spinning. By a simple deduction, I solved the problem by simply adding another lithium battery to the circuit and it worked amazingly, better than I expected! I soldered my battery charger board together to make it compatible for charging 2 batteries and it went quite well. As expected, the board helped regulated to 8.4V to charge both batteries.

Now I just need to solder everything together and I got it completed! A minor concern for me was battery overcharged protection as I didn’t know if my battery charger board could prevent that from happening or if the batteries will explode (oops). The next sunny day I went ahead and put it to the test, leaving it outside for around 2 hours or so. After that, I came back to check on it and the LED turned blueish which was amazing. It meant that the charging process for the battery worked.

After finishing that, I started to get my hands on designing again and separated each part of the fan’s body, and started the printing process. And that concluded at the end of week 5.

I should be having a bunch of stuff printed by Wednesday next week and tested out on my circuit. And by the upcoming Friday, hopefully, I will have a prototype of a fan that could work and modify from there.

Week 4: Wiring Time!

This week started off with the 3D printing problems again as the printing machine for my base went wrong (shown in pic).

I went ahead and fixed the 3D printer and got everything rolling, then tested one of my fan blades that actually fitted the motor and everything went quite well (in the video).

Later on, I started testing the solar panel with the tp5100 board (a board that helps control the energy that would be converted into batteries) and immediately see the result (red LED).

The next day when I actually tried soldering everything together and testing it out, I realized that the red LED didn’t mean it was working but rather not enough power was generated. I took measurements from the tp5100 and sure enough, it wasn’t producing enough power – the solar panel only managed to have an output of 4V instead of 10V.

Then my head was struck with 2 questions: How can I connect this to my Arduino board and the battery simultaneously? After researching online I understood that bad soldering (which was totally what I did) could lead to lower voltage because of the appearance of steel (which has R, and if we used the formula U = I / R, we can say that the voltage would decrease if the I (amps) don’t increase). Afterward, I would try to desolder the wire from the solar panel and the tp5100 and replace it with electrical tape and get it to work while still producing a good 10V as expected.

I got the solar panel stuck together with the tp5100 via electrical tape and brought it outside to test it and got super excited because it paid off.

Not everything went right though, as my base for the fan turned into a block of some sort, due to me placing it not correctly on the program before the printing, and the support got in the middle of it, essentially making it a block.

I did some research and found a schematic that would be similar to my circuit so I went ahead and applied it to mine.

The first step was to see if it’s charging the battery or not and it seems to finally work! As soon as I wire the battery to the board, the LED turns red indicating that it is charging the battery.

Eventually, I got the fan to run using the power of the solar panel and it got me excited, although it needed a bit of help to start running the motor could spin using the energy from the solar panel now, which is great! Despite that, a few problems were raised up: Does it charge the battery and power the board at the same time or not? And how would this board power itself without the help of the power from my laptop? And finally, do I want that my whole board is 2 separate parts that one is the solar panel that powered the battery and the fan part which used the battery which was charged by the solar panel? Or conjoint it together as one circuit like the schematic above.

Week 3: Getting things done

After receiving the panel from last week, at the start of this week I immediately went to solder it to wires. It took me a bit to relearn soldering again, as the last time I used the soldering tools was the previous year when I was modding my keyboard as a hobby.

After finally finishing soldering the solar panel, I turned the motor and hooked those up to wires.

Since the motor was a bit heavier and bulkier, it was hard for me to solder it correctly, and by the end of the day, the wire came off :), so I just wrapped things up and decided to do it the next day.

In addition, I had come up with models for the fans as well as its base. Although it is not the best, it should do the job for now as I am in the phase of testing things out.

I spent a good chunk of time trying to connect the motor wires to the L298N but turns out the board was not in its normal form (look at that skewness) so I got a new L298N, replaced every wire and finally, the board worked for the new motor.

Next up, since the motor was working well, I started to print out some more different fan designs (the old ones’ measurements were all wrong) as well as finish the body for the fans.

However, I didn’t really measure the motor and calculate everything carefully but eyeballing so everything I printed at this point would mostly be useless.

(the circuit couldn’t fit in the body)

In the meantime, while waiting for the printing results, I managed to get the code working and test it out properly. I settled for 5 different speed ranges: a <= 20 degrees Celcius <= b <= 25 degrees Celcius <= c <= 30 degrees Celcius <= d <= 35 degrees Celcius. (a, b, c, d stands for different speeds, the later the faster).

After discovering that my 3D print absolutely didn’t fit anything related to my circuit (and some of it was broken as well), I decided to measure things out carefully and redesigned my fan’s body, and printed again.

That was it for the third week and after that, we started to work on our presentation for the final week.

Week 2: Trial and Error

This week I started to focus on studying the basics of 3D designing in Fusion 360. I learned it myself mainly through Youtube channels called Learn Everything About Design and Product Design Online. After that, I found a prototype for the fan blades and started putting the 3D printer into use. The first few models were relatively small, so much so that it didn’t print out anything! I struggled quite a bit but then I realized the problem was the sizing, so I needed to scale that up. As the printing process finally started, it went quite well for the bottom layer of the fan. However, the problem came up only after I left it there for a couple of hours: the fan blades were not printing properly (shown in the picture).

Turns out the 3D printer is really bad at printing floating stuff, and I needed to add the support parts for the fan to print out normally. I add the support for one fan model and leave it there for printing. The next day, I came in and saw both of my products finished although it is not good looking as I think they would be. The white one would still lack the support for the fan blades which were hovering so I need to change that as for the green one, it didn’t finish printing due to the PLA being stuck so I had to redo it again.

I also add a small hole in the middle of the green fan for plugging in my motor as shown.

In addition, I tried another printer as well but after 30 minutes of inspecting, I had to stop it because the print was getting nowhere.

After that, I began to look up different fan designs and sketched the base of the fan. A few hours later, the 3D printing process would finish and I managed to peel out the support parts of the fans, leaving it like shown in the picture.

I went a bit further and get the sandpaper to scrape out the surface of the fans for it to be more flattened. Noticing that smaller fan blades than with a larger quantity of it didn’t work out as well, I opted for the bigger fan blades and less quantity and got this design out. I finally got it to print out and as expected, the support part cracked out easier than the previous two fans I had.

My solar panel had come as well so to wrap up the week, we 4 had a small talk with Josh and Eric and all decided on what to do with next week. For me, it was focusing more on the circuit for the fan and figuring out what batteries I need to buy for the circuit to work. That is the end of week 2.

Week 1: Introduction

Hello, I am Hai Doan. For this program, I’m building a solar-powered fan that consumes less energy, generates a quieter output, and provides the same or better speed as those purchased from stores that use batteries. Additionally, it has the ability to adjust speed in response to temperature. We discussed our project planning and design on the first day. A fan that can be powered by solar energy was my bare minimum requirement for a viable product. In comparison to the less expensive ones that are purchased outside, it should also be energy efficient. If you wish to use this product in real life, this feature is necessary. After achieving this minimal objective, my next goal is to add the temperature-adjusting component to the fan. Instead of needing to purchase more expensive fans with the appropriate speed, this will allow people to wander around on hot days with a cooler temperature that is entirely auto-adjustable. These are my main stretch goals, although I’m sure there’s room for the project to include more features eventually.

Day 1 included us playing a little minigame: building an object that fulfills the prompt which was written on the box using only items in that box only. We were split into 2 teams, me and Sami; Josie and Artiki. While we didn’t succeed in the given prompt, we learned that there were more resources around us than we initially thought of, and knew when to give up to approach the project in a different way. After that, we started listing out our goals and then planning out specifically what we will do in the upcoming weeks. My goal was to figure out how to connect the Arduino board to the motor and the temperature sensor to simultaneously control the fan according to the measured temperature.

On day 2 I spent most of my time familiarizing myself with the Arduino board and the other necessary components for the temperature sensor and the motor for the fan. I looked up various tutorials to deeply understand how the board worked and how to connect them together. Luckily, here in the ICL we already got a lot of things prepared so I was able to get my hands on work pretty early on. After a day, I was able to make a small circuit that displayed the temperature in the current area while also being able to control the fan.

On day 3 I started to figure out which parts I needed to buy for my project while also beginning to look into Tinkercad for 3D model design. I was creating a simple sketch for the base of the fan using blocks, but that was when I realized that Tinkercad would not be enough for an intricate fan blade design since it would need different kinds of curves to create an efficient one.

On day 4 I continued to look into designing and learned the basics of Fusion 360, a more complex program for the 3D design that would fit my needs. The learning curve for this program is harder than I imagined and I reckon that it would take a long time for me to study it well enough to be able to design. In addition, I also found some models to have a base to test/modify it.